Windows 7 load balancing network

I still have two external IP addresses connected and most programs would only choose to use either one of them since they were designed that way. What it does is it allows me to use multiple programs optimally like downloading or watching youtube videos and still be able to play games or surf with no delay or lag since both connections have their own separate line. Think of it as water pipes. Rather than widening the size of one pipe or increasing the flow of water, Network Load Balancing optimizes my speeds by adding another separate pipe.

Now, I have a more stable connection since if either one of them bugs down or is being used extensively, I still have the other to compensate. Torrent downloads work very well with load balancing since they rely on multiple connections. I tried testing on a heavily seeded torrent and I was surprised to find out that the bandwidth of both of my connections added up! One of my torrents was downloading at Also, I want to know how to set rules so that specific programs would only use a specific connection.

What I do is that before I launch program I have the other connection disabled and I open it later once the program is connected. Windows does it automatically. All you have to do is make sure both internet connections are functioning properly. Can you please tell me what torrent client you used in your tests?? And did you test it with just using one of your connections and then test it again with both connections running??

In a nutshell, Dynamic mode utilizes the best aspects of both Address Hash and Hyper-V Port and is the highest performing load balancing mode. The outbound loads in this mode are dynamically balanced based on the concept of flowlets. Just as human speech has natural breaks at the ends of words and sentences, TCP flows TCP communication streams also have naturally occurring breaks.

The portion of a TCP flow between two such breaks is referred to as a flowlet. When the dynamic mode algorithm detects that a flowlet boundary has been encountered - such as when a break of sufficient length has occurred in the TCP flow - the algorithm automatically rebalances the flow to another team member if appropriate.

In some circumstances the algorithm might also periodically rebalance flows that do not contain any flowlets. Because of this, the affinity between TCP flow and team member can change at any time as the dynamic balancing algorithm works to balance the workload of the team members. Whether the team is configured with Switch Independent or one of the Switch Dependent modes, it is recommended that you use Dynamic distribution mode for best performance.

When you configure a NIC as a Standby adapter, all other unselected team members are Active, and no network traffic is sent to or processed by the adapter until an Active NIC fails. When all team members get restored to service, the standby team member returns to standby status.

You do not need to designate a Standby Adapter to achieve fault tolerance; fault tolerance is always present whenever there are at least two network adapters in a NIC Team. To access the Primary Team Interface dialog box, you must click the link that is highlighted in the illustration below.

After you click the highlighted link, the following New Team Interface dialog box opens. You are commenting using your Google account. You are commenting using your Twitter account. You are commenting using your Facebook account. Notify me of new comments via email. Notify me of new posts via email. Skip to content Introduction NLB is a scalable, high-availability feature that you can install on all editions of Windows Server You might have to refresh the view Good luck!

Share this: Twitter Facebook LinkedIn. Like this: Like Loading Do you think NLB cluster works with Radius server? Click on Add roles and features button and skip all pages until you reach the Features section. From the features list select Network Load Balancing and proceed with the installation. Note that Powershell support for NLB will also be installed:. Now enter the local server IP address and click on Connect. Select one of the available network interfaces that will be part of the NLB process and proceed with the following section.

Note that you can add multiple IP addresses for one host. Continue the wizard by pressing the Next button. This IP address is not physically assigned to a network card and instead a virtual network adapter is created. Note that you can add multiple IPs for load balancing, but the first one will be considered the primary address. For testing purposes I will add a random IP address:. The next section is used to configure cluster parameters. Enter the cluster full internet name in my example cluster1.

A NLB cluster must operate in one of the following modes:. Unicast — the MAC address of the cluster virtual network adapter is shared with all cluster nodes. By using only one network adapter on each server, communication will be made only with devices that are part of the same subnet as the given node. All devices from all subnets can communicate with the node, but multicasting is used for cluster communication.